SUITABLE SUBSTRATES

► Concrete / Masonry.

► Concrete block.

► Cement mortar beds.

► Non-water soluble cut-back adhesive.

► Existing ceramic tile and stone.

► Consult cement backer board manufacturer for specific installation recommendations and to verify acceptability for exterior use.

APPROXIMATE COVERAGE

► 55–60sft per 20kg bag with 1/4″ x 1/4″ (6 mm x 6 mm) notched trowel.

► Coverage will vary depending on trowel notch size, type and size of tile and substrate.

SHELF LIFE

► Factory sealed containers of this product are guaranteed to be of first quality for one (1) year* if stored off the ground in a dry area.

► High humidity will reduce the shelf life of bagged product.

PACKAGING

► 1 kg, 5 kg, 20 kg bag

COLOR

► White

LIMITATIONS

► Not for use directly over particle board, luan, Masonite® or hardwood floors.

► Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use a Antique Glass Mosaic Tile Adhesive (White) Waterproofing Membrane.

NOTE

► Surfaces must be structurally sound, stable and rigid enough to support ceramic/stone tile, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations where L=span length.

CAUTIONS

► Consult MSDS for more safety information.

► Some marbles and other stone have low flexural strength and may not be suitable for installation over wood floors.

► During cold weather, protect finished work from traffic until fully cured.

► Contains portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.

► Wait 14 days after the final grouting period before filing water features with water at 70°F (21°C).

► DO NOT take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.

► Keep out of reach of children.

WORKING PROPERTIES

► Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions.

INSTALLATION:

SURFACE PREPARATION

► All surfaces should be between 40°F (14°C) and 90°F (32°C) and structurally sound, clean and free of all dirt, oil, grease, paint, concrete sealers or curing compounds. Rough or uneven concrete surfaces should be made smooth with Antique Platinum Adhesive Latex Portland Cement Underlayment to provide a wood float (or better) finish. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off. Installation may be made on a damp surface. Concrete slabs must be plumb and true to within 1/4″ (6 mm) in 10 ft (3 m).

NOTE :

► Antique Platinum Adhesive does not require a minimum cure time for concrete slabs. Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI specification A108.01-3.7 “Requirements for Movement Joints: Preparations by Other Trades” or TCNA detail EJ-171 “Movement Joints—Vertical & Horizontal”. Do not cover expansion joints with mortar.

► Installer must verify that deflection under all live, dead and impact L/360 for ceramic tile and brick or L/480 for stone installations where L=span length.

MIXING

► Place clean, potable water into a clean pail. Add Antique Platinum Adhesive. Use approximately 5-5.5 litres of water for 20kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowelable consistency. Allow mortar to slake for 5–10 minutes. Remix with out adding any more water or powder. During use, stir occasionally to keep mix fluffy. DO NOT temper with water.

APPLICATION

► Apply Antique Platinum Adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side.

NOTE :

► Use proper sized notched trowel to ensure full bedding of the tile. Spread as much mortar as can be covered with tile in 15–20 minutes. Back butter large tiles >8″ x 8″ (>200 mm x 200 mm) to provide full bedding and firm support. Place tiles into wet, sticky mortar and beat in using a beating block and rubber mallet to embed tile and adjust level. Check mortar for complete coverage by periodically removing a tile and inspecting bedding mortar transfer onto back of tile. If mortar is skinned over (not sticky), remove and replace with fresh mortar.

GROUTING

► Grout the installation after a minimum of 24 hours curing time at 70°F (21°C). Grout with Antique TG Silver Sanded Grout or Antique TG Golden Unsanded Grout mixed & Antique Platinum Grout Admix Plus. For maximum stain resistance use Antique Platinum Adhesive Stain free Grout for Floor N' Wall.

MAINTENANCE

► Antique Platinum Adhesive grouts require routine cleaning with a neutral pH soap and water. All otherAntique Platinum Adhesive materials require no maintenance but installation performance and durability may depend on properly maintaining products supplied by other manufacturers.

WARRANTY

► Antique Construction Chemical Company warrants that Antique Platinum Adhesive is free from manufacturing defects and will not break down, deteriorate or disintegrate under normal usage for a period of one (1) year from date of purchase subject to the terms and conditions stated in Antique Platinum Adhesive Product Warranty.